🚚 Free Worldwide Shipping on All Orders!Shop Now
Li-Cu-Li Composite Foil (0.1mm Li on Two sides of Cu Foil), 100g/pack (80 mm W x 6m L) - LCL2S80
HomeStore

Li-Cu-Li Composite Foil (0.1mm Li on Two sides of Cu Foil), 100g/pack (80 mm W x 6m L) - LCL2S80

Li-Cu-Li Composite Foil (0.1mm Li on Two sides of Cu Foil), 100g/pack (80 mm W x 6m L) - LCL2S80

Li-Cu-Li Composite foil is made by cold rolling double side Li foil on copper foil under dry room, which is designed to build the anode of pouch cell or cylindrical cell for new generation Li-ion battery.

SPECIFICATIONS:
Purity
  • 99.9% Lithium, 99.99% Copper
Dimension
  • Structure: Li (0.1 mm) + Cu (12um) + Li (0.1 mm)
  • Size: 80mm Width x 6000mm L x 0.21 mm Thickness (Li layer width 80mm; Cu layer width 100mm)
  • Weight:100g/roll 
Average Density
  •  ~0.94 g/cm2
Package
  • Packed a steel container filled under dry room (RF < 2%)
Use
  • Clean the surface of the lithium foil using a nylon brush/stainless steel scalpel until a shiny silvery surface appears (inside an argon glovebox)
Shipping Limitations
  • Shipments of lithium foil are described as “UN 1415, Lithium, 4.3, PG I"
    All shipments are Hazard Class 4.3 and require “Dangerous when wet” labels
    Sea Class 4.3 (IMDG)
    Road, Rail Class 4.3 11a (RID/ADR)
Safety Data Sheet
Operation
  • Package must be opened and stored inside a glove box with Argon Gas and moisture less than 8 ppm and O2 less than 2 PPM. Never use N2 gases in glovebox!!!
Notes
  • MTI only sells the Li foil within the USA and does not accept international orders due to restrictions on hazard material exportation!!!
  • Operation and Storage: Lithium is very active in the air, please carefully read the SDS carefully.
  • Lithium foil may be oxidized during handling and storage. if you find any oxidation on the surface of the Li-chip, please use sandpaper to remove it before using it.
  • Li foil may have a passivation layer, from our customer experience, removing the passivation layer will increase your battery capacity
  • If the Li metal is stored in mineral oil, please refer to this guide on How to clean mineral oil off Lithium metal using anhydrous Toluene
  • The lithium foil was packed in the dry room with < 10 PPM H2O. Therefore, a slight increase of O2 PPM level might be seen in the glove box when the can is opened. Please keep purging the glove box with ultra-high purity Ar until the required O2 PPM level is reached.
  • No return or refund for misusing or wrong storage which causes lithium foil oxidation.
 Q &A
  • Why Can not sell in a small package? A: Small package will cost more from a manufacturer
  • Why Li-Chip so expensive? A: Because of shipping regulations from packing to shipping will cost 90% or more.

Lithium Storage Options


53L Vacuum Chamber SVC-6050


Glovebox

 

$2,998.00
Li-Cu-Li Composite Foil (0.1mm Li on Two sides of Cu Foil), 100g/pack (80 mm W x 6m L) - LCL2S80—
$2,998.00

Li-Cu-Li Composite Foil (0.1mm Li on Two sides of Cu Foil), 100g/pack (80 mm W x 6m L) - LCL2S80

Li-Cu-Li Composite foil is made by cold rolling double side Li foil on copper foil under dry room, which is designed to build the anode of pouch cell or cylindrical cell for new generation Li-ion battery.

SPECIFICATIONS:
Purity
  • 99.9% Lithium, 99.99% Copper
Dimension
  • Structure: Li (0.1 mm) + Cu (12um) + Li (0.1 mm)
  • Size: 80mm Width x 6000mm L x 0.21 mm Thickness (Li layer width 80mm; Cu layer width 100mm)
  • Weight:100g/roll 
Average Density
  •  ~0.94 g/cm2
Package
  • Packed a steel container filled under dry room (RF < 2%)
Use
  • Clean the surface of the lithium foil using a nylon brush/stainless steel scalpel until a shiny silvery surface appears (inside an argon glovebox)
Shipping Limitations
  • Shipments of lithium foil are described as “UN 1415, Lithium, 4.3, PG I"
    All shipments are Hazard Class 4.3 and require “Dangerous when wet” labels
    Sea Class 4.3 (IMDG)
    Road, Rail Class 4.3 11a (RID/ADR)
Safety Data Sheet
Operation
  • Package must be opened and stored inside a glove box with Argon Gas and moisture less than 8 ppm and O2 less than 2 PPM. Never use N2 gases in glovebox!!!
Notes
  • MTI only sells the Li foil within the USA and does not accept international orders due to restrictions on hazard material exportation!!!
  • Operation and Storage: Lithium is very active in the air, please carefully read the SDS carefully.
  • Lithium foil may be oxidized during handling and storage. if you find any oxidation on the surface of the Li-chip, please use sandpaper to remove it before using it.
  • Li foil may have a passivation layer, from our customer experience, removing the passivation layer will increase your battery capacity
  • If the Li metal is stored in mineral oil, please refer to this guide on How to clean mineral oil off Lithium metal using anhydrous Toluene
  • The lithium foil was packed in the dry room with < 10 PPM H2O. Therefore, a slight increase of O2 PPM level might be seen in the glove box when the can is opened. Please keep purging the glove box with ultra-high purity Ar until the required O2 PPM level is reached.
  • No return or refund for misusing or wrong storage which causes lithium foil oxidation.
 Q &A
  • Why Can not sell in a small package? A: Small package will cost more from a manufacturer
  • Why Li-Chip so expensive? A: Because of shipping regulations from packing to shipping will cost 90% or more.

Lithium Storage Options


53L Vacuum Chamber SVC-6050


Glovebox

 

Product Information

Shipping & Returns

Description

Li-Cu-Li Composite foil is made by cold rolling double side Li foil on copper foil under dry room, which is designed to build the anode of pouch cell or cylindrical cell for new generation Li-ion battery.

SPECIFICATIONS:
Purity
  • 99.9% Lithium, 99.99% Copper
Dimension
  • Structure: Li (0.1 mm) + Cu (12um) + Li (0.1 mm)
  • Size: 80mm Width x 6000mm L x 0.21 mm Thickness (Li layer width 80mm; Cu layer width 100mm)
  • Weight:100g/roll 
Average Density
  •  ~0.94 g/cm2
Package
  • Packed a steel container filled under dry room (RF < 2%)
Use
  • Clean the surface of the lithium foil using a nylon brush/stainless steel scalpel until a shiny silvery surface appears (inside an argon glovebox)
Shipping Limitations
  • Shipments of lithium foil are described as “UN 1415, Lithium, 4.3, PG I"
    All shipments are Hazard Class 4.3 and require “Dangerous when wet” labels
    Sea Class 4.3 (IMDG)
    Road, Rail Class 4.3 11a (RID/ADR)
Safety Data Sheet
Operation
  • Package must be opened and stored inside a glove box with Argon Gas and moisture less than 8 ppm and O2 less than 2 PPM. Never use N2 gases in glovebox!!!
Notes
  • MTI only sells the Li foil within the USA and does not accept international orders due to restrictions on hazard material exportation!!!
  • Operation and Storage: Lithium is very active in the air, please carefully read the SDS carefully.
  • Lithium foil may be oxidized during handling and storage. if you find any oxidation on the surface of the Li-chip, please use sandpaper to remove it before using it.
  • Li foil may have a passivation layer, from our customer experience, removing the passivation layer will increase your battery capacity
  • If the Li metal is stored in mineral oil, please refer to this guide on How to clean mineral oil off Lithium metal using anhydrous Toluene
  • The lithium foil was packed in the dry room with < 10 PPM H2O. Therefore, a slight increase of O2 PPM level might be seen in the glove box when the can is opened. Please keep purging the glove box with ultra-high purity Ar until the required O2 PPM level is reached.
  • No return or refund for misusing or wrong storage which causes lithium foil oxidation.
 Q &A
  • Why Can not sell in a small package? A: Small package will cost more from a manufacturer
  • Why Li-Chip so expensive? A: Because of shipping regulations from packing to shipping will cost 90% or more.

Lithium Storage Options


53L Vacuum Chamber SVC-6050


Glovebox

 

You may also like

-65%NEW
Thumbnail 1Thumbnail 2

Magnesium (Mg) Foil: 100mm Width x 0.1 mm thick x 1000 mm Length, MF-Mg18L1000

$299.00

$104.65

NEW
Thumbnail 1Thumbnail 2

100 g Polycrystalline Silicon Powder, 4N Purity, APS 1 Micron - Lib-Si1000

$295.00

-65%NEW
Thumbnail 1

Zn - Polycrystalline Metallic Foil: 0.1mm thick x 100mm Width x 1400 mm Length - MF-Zn1400L

$198.00

$69.30

NEW
Thumbnail 1Thumbnail 2

Nickel Oxide Powder (NiO) SOFC Anode Powder, 500g/Pack - EQ-SOFC-NiO

$399.00

-65%NEW
Thumbnail 1Thumbnail 2

Silicon/Carbon (Si/C) Composite Powder as Lithium Ion Battery Anode, 200g/bottle - Lib-SC450B

$198.00

$69.30

-65%NEW
Thumbnail 1Thumbnail 2

Li-Ion Battery Anode - Single Layer CMS Graphite Coated on Cu Foil (241 L x 200 W x 0.05 T, mm) 5 sheets/bag - bccf-ss

$179.00

$62.65

-65%NEW
Thumbnail 1Thumbnail 2

Li-Ion Battery Anode -Double Layer CMS Graphite Coated on Copper Foil (241mm L x 200mm W x 90um Thick) 5 sheets/bag bccf-ds

$259.00

$90.65

-65%NEW
Thumbnail 1

Li4Ti5O12 (Titanate) Powder for Li-ion Battery Anode, 150g/bag - Lib-LTO

$149.00

$52.15

NEW
Thumbnail 1

Lithium Chip 16 Dia x 0.2/0.6/1.0 thick (mm) for Li-ion Battery R&D, 300pcs / bottle - EQ-Lib-LiC

$796.00

-65%NEW
Thumbnail 1

Artificial Graphite Powder for Li-ion Battery Anode, 200 g/bag - Lib-CMSG

$125.00

$43.75

-65%NEW
Thumbnail 1

Hard Carbon Powder for Sodium Ion Battery Anode, 200g/bottle, SIB-BHC300

$249.00

$87.15